Pyro-Putty ® High Temperature Ceramic-Metallic Putties are used to seal joints and repair defects in cast aluminum, cast iron, steel and stainless steel. Formulated using the most advanced organic and inorganic-ceramic resin technologies, these advanced materials resist temperatures to 2000 °F. DESIGN GUIDELINES FOR THE SELECTION AND USE Stainless steels are iron-base alloys containing 10.5% or more chro- possibly for high-temperature conditions involving high acid and chloride con-tents), it resists organic chemicals, environments are based on a long history of successful application, but they are intended only as guidelines. Small
1000°F High Temperature Aluminum Putty:Durabond 7025 was specially formulated with active aluminum to provide excellent resistance to corrosion, cavitation, most chemicals and solvents. Just mix to a smooth creamy paste and trowel on. Cures in 24 hours at room temp. or in 2 hours at 250ºF to form a highly machinable, aluminum based composite usable to 1000ºF. High- Performance Stainless Steelsthese stainless steels at temperatures above 500°C (930°F) is limited. In addition, care must be taken to avoid forming damaging amounts of these phases during high temperature operations such as forging or welding. A list of notable wrought high-performance austenitic stainless steels is given in Table 1. Grades are identified by the name by High-Temperature Resistance Protective Coatings PPG PPG HI-TEMP 1027 Prevents Corrosion Under Insulation (CUI) of carbon and stainless steel over an extreme temperature range from -185°C to 650°C (-300°F to 1,200°F). Simple to use with a proven track record and excellent results, also providing UV stability to prevent corrosion of non-insulted surfaces subject to atmospheric exposure.
Dec 01, 2016 · The material used in the present study is 304 Stainless Steel, the chemical composition of it is shown in Table I.They were supplied as sheets from Metal Depot, US. with thickness of 4 mm and are cut to 15mm X 15 mm X 4 mm specimens and used directly without further surface preparation. The immersion solution is 0.5, 1, 1.5 and 2% KCl that is prepared from anhydrous KCl (99% purity) KBS Coatings 65123 Stainless Steel Xtreme Temperature 2. This is paint for high temperature applications. NOTES - BTW:A. Volatile - smells up the room. (have ventilation - open window) B. Dries quick to get 2nd coat on 5 minutes later. C. Painted/Covered bare metal in seconds. D. Not much time to work with. E. Tried to apply w paper towel method, but wouldn't work, too volatile. Lubricants SwagelokHalocarbon-based thread lubricant for use on titanium, stainless steel, steel, and nickel-based alloys. For use at temperatures up to 350°F (176°C). Silver Goop Oil-based thread lubricant for use on stainless steel and high-temperature alloys. For use at temperatures up to 1500°F (815°C).
Monel® 400 is a nickel-copper alloy with high strength and excellent corrosion resistance in a range of media including sea water, hydrofluoric acid, sulfuric acid and alkalies. Monel® 400 is used for marine engineering, chemical and hydrocarbon processing equipment, valves, pumps, shafts, fittings, fasteners and heat exchangers. Permatex® Nickel Anti-Seize Lubricant PermatexProtects metal parts from seizing and galling at temperatures up to 2400°F (1316°C). It is recommended where copper contamination must be avoided, under conditions of extreme pressure and temperature, and with stainless steel, titanium and nickel alloys. Ready-to-use Metal Repair and Patching CompoundLab-metal withstands temperatures as high as 350ºF (and as low as -40 o F) and when hard, can be painted with lacquer or enamel without danger of bubbling, lifting paint, chipping or peeling. Lab-metal stands up to normal paint baking procedures and may also be powder coated (see special powder coating instructions).
P. Kritzer, N. Boukis, E. Dinjus, Review of the Corrosion of Nickel-Based Alloys and Stainless Steels in Strongly Oxidizing Pressurized High-Temperature Solutions at Subcritical and Supercritical Temperatures, CORROSION. 2000;56(11):1093-1104. SAF-T-EZE Stainless Steel Grade Anti-seizeSAF-T-EZE ® Stainless Steel Grade Anti-Seize provides ultimate protection as a high temperature anti-seize and extreme pressure lubricant. Stainless Steel Anti-Seize stops corrosion, galling and seizure between metal parts and is recommended for service to 2500ºF (1370ºC). SAF-T-EZE Stainless Steel Grade Anti-seizeSAF-T-EZE ® Stainless Steel Grade Anti-Seize provides ultimate protection as a high temperature anti-seize and extreme pressure lubricant. Stainless Steel Anti-Seize stops corrosion, galling and seizure between metal parts and is recommended for service to 2500ºF (1370ºC).
Tuff Temp Corp. offers a complete line of Textile products (Woven Tapes & Sleeves, Knitted Sleeves, Non-Woven Needle Punched Felts & Ropes) based on Stainless Steel (316L) fibers whice offer unmatched heat resistance (up to 650 C / 1200 F) and excellent performance in many glass making applications such as Automotive Glass, Glass Bottles and Cathode Ray Tube (TV) Glass. Thermophysical Properties of Materialsthermophysical data of high temperature organic coolants, molten salts and other advanced coolants, which have not yet found application in nuclear engineering, in spite of continuing attempts. What is high temperature hydrogen attack (HTHA)/hot McLaughlin J E, A qualitative risk-based assessment procedure for high temperature hydrogen attack of C-1/2Mo steel, Proceedings, ASME Pressure Vessels and Piping Conference (PVP2007), and the Eighth International Conference, Creepand Fatigue at Elevated Temperatures (CREEP8), PVP2007-26129, 22-26
Stainless steels are mainly used for their re-sistance to aqueous corrosion but are also widely used at high temperatures when carbon and low-alloyed steels do not pro-vide adequate corrosion resistance and/or strength. They can be found in applications in which high-temperature oxidation resist-ance or high-temperature strength are re-quired .